forsol
X
全部分類

技術與服務

TECHNIACL AND SERVICE

PV-15T11C產品說明書

  • 分類:技術與服務
  • 發布時間:2020-06-04 00:00:00
  • 訪問量:0
概要:
概要:
詳情

PV-15T11C產品說明書
PV-15T11C Product Manual

感謝您選用浙江弗沙朗能源股份有限公司生產的太陽能光伏接線盒產品。為使您能正確、快速、安全地使用該產品,使用前請您詳細閱讀本說明書。
Thank you for your choose our solar PV junction box. To enable you can use of this product correct, fast and safe, please read this manual before using.
一、產品結構及尺寸:
Product structure and size


二、技術參數:
Technical parameters
適用的組件功率Suit for: 200~400W
  最大工作電壓maximum working voltage: 100V
額定沖擊電壓Rated impulse voltage: 12000/16000V DC
額定電壓Rated Voltage: 1500V
        接觸電阻contact resistance: ≤0.5mΩ 
額定電流Rated Current: 15A 
反向電流reverse current: 30A  
安全等級Safety Class: Class II  
線纜范圍Wire Size Range: 4mm2 
溫度范圍Ambient Temperature Range: -40℃~+85℃ 
防護等級Protection Degree: IP68 
阻燃等級Flame Resistance: UL94-V0 
三、安裝注意事項: 
Install Caution 
1.在正式安裝接線盒時,首先應確認該電池組件不在工作狀態。如果一定要在陽光照射下安裝,請 
采用安全可靠的遮陽罩遮住電池組件,以免其產生電流,引起電擊。人體不能同時接觸連接器系統的 
正負極,以免發生觸電; 
In the formal installation, you should confirm the solar module is not in working condition. If must be installed under the sunlight, please use the sun shade cover the solar module, in order to avoid its working, cause electric shock. Worker cannot contact the positive pole and negative pole at the same time, so as to avoid electric shock 
2.使用前接線盒蓋是松開的,接線完畢后確保將接線盒蓋好封嚴; 
The junction box cover is open before using, the connection after the junction box to ensure that good sealing 
3.接線端子的正負極、電纜的正負極是明確規定的,用戶不要自行調換極性或反接,這樣可能會造 
成嚴重的后果; 
The positive pole and negative pole for terminal and the cable is clearly defined, and the user should not change or make them reverse, which may cause serious consequences. 
4.如果要進行系統維護,請務必使系統處于停止工作狀態后再進行; 
For system maintenance, please make sure that the system is stopped working; 
5. 請勿對接線盒、連接器、電纜施加外力或重壓, 對電纜線的拉力<400N; 
Do not force or the weight of junction box, connector and cable, the cable tension is less than 400N; 
6.推薦使用脫醇和脫丙酮型硅膠;如果使用脫肟型硅膠,在生產儲存過程中,必須使硅膠中的2-丁酮肟完全揮發出去,否則可能導致塑件部件開裂,金屬件被腐蝕等不良現象。 
Recommend the use of de ethanol and acetone silica removal; if the use of oxime type silica removal, in the process of production and storage must be completely evaporate silica gel of 2-butanone oxime, otherwise it may cause plastic parts cracking and metal parts are corrosion and other undesirable phenomena. 
四、安裝及使用方法 
Installation and usage 紅色為硅膠涂抹區連接板穿線孔

 
接線盒內部灌膠約30ML 上蓋蓋入順序 


1. 如所示紅色區域為硅膠涂抹區,涂抹方式為沿打膠筋涂入硅膠,待沿打膠筋旋轉一圈后將底盒壓入背板上。 2. 匯流條從底盒底部從下望上穿入連接板穿線孔,再用電烙鐵把匯流條焊住。 
3. 如圖三所示灌膠順序灌入密封膠,注意膠面與水平面水平,實際灌膠量約30ML 
4. 灌膠后需要將底盒放置于陰涼處等待膠液凝固,待凝固后方可蓋上上蓋。上蓋蓋入順序為1-2-3.即 
先扣入底盒頂端(1)處兩個卡扣,再扣入底盒下端(2)處一個卡扣,再扣入左右(3)處兩個卡扣。 
1 as shown in the red area is the silica gel coating area, the way is to apply the adhesive tape along the gel, to be the bottom of the box to be pressed into the back of the box. 
2 bus from the bottom of the bottom of the box from looking down on the threading hole passes through the connection plate, and the handle of the electric iron bars soldered. 
3 in Figure three shows that the filling in the order of the glue, the glue surface and the level of the level, the actual amount of plastic 30ML 
4 after the need to fill the bottom of the box is placed in a cool place to wait for the glue to solidify, to be solidified before the cover can be covered. The upper cover is in the order of 1-2-3. is 
The top (1) of the bottom box is deducted, and then the bottom (2) of the bottom of the box is a snap, and then buckle into the left and right (3).

掃二維碼用手機看

聯系我們

 

總機:0573-88188870

公眾號二維碼

掃一掃,關注我們公眾號

 浙江弗沙朗能源股份有限公司 Copyright 網站建設:中企動力 溫州       浙ICP備13031007號-2

雪梨直播软件_雪梨直播平台_雪梨直播app下载安装_雪梨直播苹果